This page in other versions: 9.0 / 9.1 / 9.2 / 9.3 / 9.4  |  Development versions: devel  |  Unsupported versions: 7.3 / 7.4 / 8.0 / 8.1 / 8.2 / 8.3 / 8.4

pg_resetxlog

Name

pg_resetxlog -- reset the write-ahead log and other control information of a PostgreSQL database cluster

Synopsis

pg_resetxlog [ -f ] [ -n ] [ -o oid ] [ -x xid ] [ -m mxid ] [ -O mxoff ] [ -l timelineid,fileid,seg ] datadir

Description

pg_resetxlog clears the write-ahead log (WAL) and optionally resets some other control information stored in the pg_control file. This function is sometimes needed if these files have become corrupted. It should be used only as a last resort, when the server will not start due to such corruption.

After running this command, it should be possible to start the server, but bear in mind that the database may contain inconsistent data due to partially-committed transactions. You should immediately dump your data, run initdb, and reload. After reload, check for inconsistencies and repair as needed.

This utility can only be run by the user who installed the server, because it requires read/write access to the data directory. For safety reasons, you must specify the data directory on the command line. pg_resetxlog does not use the environment variable PGDATA.

If pg_resetxlog complains that it cannot determine valid data for pg_control, you can force it to proceed anyway by specifying the -f (force) switch. In this case plausible values will be substituted for the missing data. Most of the fields can be expected to match, but manual assistance may be needed for the next OID, next transaction ID, next multitransaction ID and offset, WAL starting address, and database locale fields. The first five of these can be set using the switches discussed below. pg_resetxlog's own environment is the source for its guess at the locale fields; take care that LANG and so forth match the environment that initdb was run in. If you are not able to determine correct values for all these fields, -f can still be used, but the recovered database must be treated with even more suspicion than usual: an immediate dump and reload is imperative. Do not execute any data-modifying operations in the database before you dump; as any such action is likely to make the corruption worse.

The -o, -x, -m, -O, and -l switches allow the next OID, next transaction ID, next multitransaction ID, next multitransaction offset, and WAL starting address values to be set manually. These are only needed when pg_resetxlog is unable to determine appropriate values by reading pg_control. Safe values may be determined as follows:

  • A safe value for the next transaction ID (-x) may be determined by looking for the numerically largest file name in the directory pg_clog under the data directory, adding one, and then multiplying by 1048576. Note that the file names are in hexadecimal. It is usually easiest to specify the switch value in hexadecimal too. For example, if 0011 is the largest entry in pg_clog, -x 0x1200000 will work (five trailing zeroes provide the proper multiplier).

  • A safe value for the next multitransaction ID (-m) may be determined by looking for the numerically largest file name in the directory pg_multixact/offsets under the data directory, adding one, and then multiplying by 65536. As above, the file names are in hexadecimal, so the easiest way to do this is to specify the switch value in hexadecimal and add four zeroes.

  • A safe value for the next multitransaction offset (-O) may be determined by looking for the numerically largest file name in the directory pg_multixact/members under the data directory, adding one, and then multiplying by 65536. As above, the file names are in hexadecimal, so the easiest way to do this is to specify the switch value in hexadecimal and add four zeroes.

  • The WAL starting address (-l) should be larger than any file name currently existing in the directory pg_xlog under the data directory. These names are also in hexadecimal and have three parts. The first part is the "timeline ID" and should usually be kept the same. Do not choose a value larger than 255 (0xFF) for the third part; instead increment the second part and reset the third part to 0. For example, if 00000001000000320000004A is the largest entry in pg_xlog, -l 0x1,0x32,0x4B will work; but if the largest entry is 000000010000003A000000FF, choose -l 0x1,0x3B,0x0 or more.

  • There is no comparably easy way to determine a next OID that's beyond the largest one in the database, but fortunately it is not critical to get the next-OID setting right.

The -n (no operation) switch instructs pg_resetxlog to print the values reconstructed from pg_control and then exit without modifying anything. This is mainly a debugging tool, but may be useful as a sanity check before allowing pg_resetxlog to proceed for real.

Notes

This command must not be used when the server is running. pg_resetxlog will refuse to start up if it finds a server lock file in the data directory. If the server crashed then a lock file may have been left behind; in that case you can remove the lock file to allow pg_resetxlog to run. But before you do so, make doubly certain that there is no postmaster nor any backend server process still alive.

Privacy Policy | About PostgreSQL
Copyright © 1996-2014 The PostgreSQL Global Development Group